Gus
-
Posts
7 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by Gus
-
-
md5 is NOT correct.
The MD5 i get from downloaded file is : ab03b5eeb1fe280ab8266302dab1b380
-
Thank you very much, tested and works fine.
-
@DaRk MaDnEsS
Can you please repost your last working version?? i think it was at 6-2, until you fix the new one.
Thanks.
-
During installation of windows while registers components the program starts to run and pops up first run messages and first run messages through internet explorer, if you could fix this and make it silent.
Thanks for tha addon, Gus.
-
@Gus: Already tested on chinese and english XP,work fine either as addon integrating into XP resource for xp setup or as silent installer on running XP.
1st of all,you should check MD5 of the downlload file,
then what integrator do you use?
i'm nlite user,obviously,entries for nlite,honest,i know a little about Raym Integrator even dont know how to write entrties for it,so not sure it work for Raym integrator.
,you can check svcpack.inf whether command-line has been integrated (see below code SetupHotfixesToRun section and check SVCPACK folder whether vbox.exe file already has been added.
[SetupHotfixesToRun]
VBox.exevbox will be installed at time left 13min during xp setup.
thanks for the report,but i amnot sure what cause the problem for you,ill do my best.
Hi, well MD5 it's ok!
I use nlite 1.4.9.1 only for my integrations. VBOX.EXE is placed at \I386\SVCPACK but it doesn't work for me!!!
I created 3 times my xp but it didn't work.
And also when i run VBOX.EXE after installation as a silent install, it doesn't either install.
Nothing Happens!!!
Maybe another addon creates the problem?? really don't know, If you have any idea to try please tell me!
Thanks for your time, and A Happy New Year!!!
-
hello guys ,Sun has released VirtualBox version2.1.0 on dec 17,2008
whats changed in this new version
This version is a major update. The following major new features were added:
+) Support for hardware virtualization (VT-x and AMD-V) on Mac OS X hosts (for Mac OS installer)
Support for 64-bit guests on 32-bit host operating systems (experimental; see user manual, chapter 1.6, 64-bit guests, page 16)
+) Added support for Intel Nehalem virtualization enhancements (EPT and VPID; see user manual, chapter 1.2, Software vs. hardware virtualization (VT-x and AMD-V), page 10))
+) Experimental 3D acceleration via OpenGL (see user manual, chapter 4.8, Hardware 3D acceleration (OpenGL), page 66)
+) Experimental LsiLogic and BusLogic SCSI controllers (see user manual, chapter 5.1, Hard disk controllers: IDE, SATA (AHCI), SCSI, page 70)
+) Full VMDK/VHD support including snapshots (see user manual, chapter 5.2, Disk image ?les (VDI, VMDK, VHD), page 72)
+) New NAT engine with signi?cantly better performance, reliability and ICMP echo (ping) support (bugs #1046, #2438, #2223, #1247)
+) New Host Interface Networking implementations for Windows and Linux hosts with easier setup (replaces TUN/TAP on Linux and manual bridging on Windows)
enjoy!
Tested 2.1.0 and not working, it doesn't install at all and no error messages.
If you could please fix this!
Thanks.
DVDFab HD Decrypter V5.x + V6.x AddonBuilder
in WPI, nLite and RVM Addons
Posted
Thanks for these addon creators, while version 5 works fine, version 6 don't work it generates 2 critical errors and stops. tried it with official dvdfab 6.0.1.0
Here's a screenshot of the installation :