Guest Posted December 17, 2012 Share Posted December 17, 2012 (edited) Hi,i installed win8 pro, i turn on adsl modem but local area connection is limited always and with yellowexclamation on task-bar.sometimes it connect to the Internet about 30 second and then yellowexclamation is revert back. i disabled ipv6 with this command but still dont work.netsh interface ipv6 6to4 set state disablednetsh interface teredo set state disabled.is there anyway to fix this?this is a ipconfig.all that windows genereted.Windows IP Configuration Host Name . . . . . . . . . . . . : hoampc Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : NoPPP adapter Broadband Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadband Connection Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 4.199.110.168(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 DNS Servers . . . . . . . . . . . : i removed this 4.2.2.1 NetBIOS over Tcpip. . . . . . . . : DisabledEthernet adapter Ethernet: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-0F-EA-63-7D-B0 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 189.100.30.100(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : i removed this Lease Expires . . . . . . . . . . : i removed this Default Gateway . . . . . . . . . : 189.100.30.50 DHCP Server . . . . . . . . . . . : 189.100.30.50 DNS Servers . . . . . . . . . . . : 189.100.30.50 189.100.30.50 NetBIOS over Tcpip. . . . . . . . : Disabledroute.print.txt===========================================================================Interface List 20...........................Broadband Connection 12...00 0f ea 63 7d b0 ......Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller 1...........................Software Loopback Interface 1===========================================================================IPv4 Route Table===========================================================================Active Routes:Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 189.100.30.50 189.100.30.100 4245 0.0.0.0 0.0.0.0 On-link 4.199.110.168 21 4.199.110.168 255.255.255.255 On-link 4.199.110.168 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 4531 127.0.0.1 255.255.255.255 On-link 127.0.0.1 4531 127.255.255.255 255.255.255.255 On-link 127.0.0.1 4531 189.100.30.0 255.255.255.0 On-link 189.100.30.100 4501 189.100.30.100 255.255.255.255 On-link 189.100.30.100 4501 189.100.30.255 255.255.255.255 On-link 189.100.30.100 4501 224.0.0.0 240.0.0.0 On-link 127.0.0.1 4531 224.0.0.0 240.0.0.0 On-link 189.100.30.100 4501 224.0.0.0 240.0.0.0 On-link 4.199.110.168 21 255.255.255.255 255.255.255.255 On-link 127.0.0.1 4531 255.255.255.255 255.255.255.255 On-link 189.100.30.100 4501 255.255.255.255 255.255.255.255 On-link 4.199.110.168 276===========================================================================Persistent Routes: NoneIPv6 Route Table===========================================================================Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link===========================================================================Persistent Routes: None Edited December 17, 2012 by mona Quote Link to comment Share on other sites More sharing options...
sp0iledbrat Posted December 17, 2012 Share Posted December 17, 2012 You can't have a Class A IP address, a broadcast subnet and a 0.0.0.0 Gateway at the same time? You need to fix the subnet and enter the gateway IP at the least. Or enable DHCP, which the router should support. Cheers Quote Link to comment Share on other sites More sharing options...
Guest Posted December 17, 2012 Share Posted December 17, 2012 how do this? Quote Link to comment Share on other sites More sharing options...
mirecek1965 Posted December 18, 2012 Share Posted December 18, 2012 DHCP Enabled. . . . . . . . . . . : No, there must be "Yes". Open Network Center, Change Adapter settings, right click, properties, Internet Protocol Version 4 (TCP/IPv4, obtain IP address automatically. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.